menu

Teltonika FM4200

Teltonika FM4200 is a heavy vehicle GPS/GLONASS terminal that is suitable for working on vans and trucks. It is able to send the coordinates and different status messages of the vehicle.

Mostrar más

That device has a rechargeable battery and smart power management controller. FM4200 has a capacious built-in memory chip that can store 7.500 records. FM4200 model is very functional with its 8 inputs and 4 outputs for managing vehicle devices.

Package contents

Teltonika FM4200 device is supplied to the customer in a cardboard box containing all the equipment that is necessary for operation. The package contains:

  • FM4200 device;
  • GNSS antenna;
  • USB cable;
  • A card, which contains URL to download FM4200 device drivers and Configurator software.

Location and tracking

FM4200 model is embedded with chip that supports both GPS and GLONASS. It doesn’t support Assisted GPS (A-GPS) technology. As the back-up, when no satellites signals are available, it uses Cell ID location (also known as LBS-tracking).

The tracking mode is flexible configured: by moving every 100m, and every 60 sec, and on turning on 30 degrees by default. When there is no movement (detected by “Ignition” status), tracker sends data every 180 seconds.

Mobile networks

FM4200 can work with GSM 2G networks.

Interfaces

FM4200 model features such interfaces as

  • RS232 port
  • Audio port
  • 4 digital inputs
  • 4 analog inputs
  • 4 open collector outputs
  • Fuel counter inputs
  • 1Wire® temperature sensor
  • 1Wire® iButton

Power supply

FM4200 uses voltage range 10-30V, which makes possible to install it both on cars and trucks. Device also features an optional built-in rechargeable backup battery. When fully charged it ensures about 1 hour of device operation (in normal conditions).

“Ignition” status

There is a virtual “Ignition” flag in FM4200 which is determined by either:

  • External power voltage – when the power level falls below a certain configured level (by default 13V), the “Ignition” is considered to be OFF, otherwise – ON.
  • Digital Input #1 – if there is positive signal on DIN #1 of the socket, the “Ignition” flag is ON.
  • Acceleration sensor – when the built-in accelerometer detects movement, the “Ignition” flag is ON.

“Stop/Movement” mode

Teltonika FM4200 determines whether vehicle is on move or stopped by one of three methods (configurable by user):

MethodMovingStopped
by Board VoltageIf board voltage exceeds certain level (configurable, 13V by default)If board voltage is lower than a certain level
by AccelerationInternal accelerometer detects movementInternal accelerometer does not detect movement
by GNSSGNSS is fixed and speed is above 5 km/hGNSS is fixed and speed is below 5 km/h  or GNSS is not fixed

Two sleep modes

FM4200 is able to go to Sleep mode after configurable Sleep timeout. This timeout (defined period) starts counting when device is in STOP mode. After timeout is reached and all conditions for sleep mode are met, device goes to normal sleep or deep sleep mode:

  • Normal sleep mode. While in normal sleep mode, FM4200 turns GNSS module OFF, but keeps GSM module ON. The device is not making any new periodic GPS records, just monitoring the events with the last known coordinates and sends them to tracking server. As a result power consumption decreases allowing saving vehicle’s battery (below 2 mA).

FM4200 exists normal sleep mode when “Movement” mode detected or “Ignition” switches on.

  • Deep sleep mode. While in deep sleep mode, FM4200 sets both GNSS receiver and GSM/GPRS module to OFF state, thus making impossible to wake up the device remotely. Battery consumption drops below 2 mA.

FM4200 exits deep sleep mode if at least one of following conditions is true:

    • “Movement” mode is detected
    • “Ignition” is turned on
    • USB cable is connected

Local and remote management

Teltonika FM4200 tracker can’t be controlled over GPRS, though it supports firmware updating via GPRS (FOTA). However, there is a wide list of SMS commands in a ASCII  format, on which device always replies back. In particular, Server address and port, APN settings can be applied remotely with SMS. To decrease the amount of SMS required for configuration SMS in binary format can be also used.

You can also configure FM4200 from a PC using proprietary software (Teltonika Configurator) and standard USB-cable which is included into package.

LED Indication

FM4200 has two status LEDs:

  • Status LED: indicates system Power
  • Navigation LED: indicates GPS reception

Integración de Servidor

Servidor de la EUtracker.navixy.com (52.57.1.136)
Servidor de la UStracker.us.navixy.com (13.52.37.2)
Puerto de servidor47776
Integrado11/10/2013

Información general

PurposeVehículo
InstalaciónProfesional

Alojamiento

Peso250 g (8.82 oz.)
Tamaño100x70x25 mm (3.94x2.76x0.98 in)

Localización GNSS

Antena interna (GNSS)
Antena externa (GNSS)
GPS
GLONASS

Conectividad

Tipo de la red del celularGSM 900/1800
Antena interna (Conexión)No
Antena externa (Conexión)No
Generación de red celular2G

Interfaces

Número de Interfaces RSC2321
Número de salidas4
Número de entradas (todos tipos)8
Entradas digitales
Soportado
Entrada análoga
Soportado
Interfaz RS232
Interfaz 1-Wire
Salidas

Hardware extras

Lectura del identificador del conductor
Soportado

Características de rastreo

Modos de rastreoIntervalo, Continuo
Localización por Cell ID
Soportado
Consumo inteligente de batería
Soportado
ECO driving
Soportado

Monitoreo de eventos

Poca batería
Soportado
Cambio de entrada
Soportado
Corte de alimentación externa
Soportado

Automonitoreo

Nivel de señal
Soportado
Nivel de señal GNSS
Soportado
Satélites GNSS fijados
Soportado
Voltaje de alimentación externa
Soportado
Nivel de batería interna
Soportado

Leyendo CAN/OBDII

Tipo de lector CAN/OBDII
Soportado
Parámetros CAN/OBDIIFuel level, fuel consumption, engine RPM, throttle position and other

Administración remota

La conexión con servidor por SMS
Soportado
Configuración remota de dispositivoSí (por SMS), Sí
Control remoto de las salidasSí, Sí (por SMS), Por GPRS (se requiere el firmware 42.XX.XX)
Soportado
Actualización de firmware OTA

Certificacón

CE
FCC
Active un dispositivo en la plataforma Probar
¿No ha encontrado su dispositivo? Podemos añadirlo Integrar
Rastreo 3.0 NEW
Open
Rastreo 3.0 NEW
Miles de objetos.
Intuitiva UX.
Poderoso diseño.
Saber más >
Open

Este sitio usa cookies.
Revise nuestra Política de Privacidad para saber más.

Do you want to switch to English version?

Yes No