TopFlyTech model T8808A is a compact and affordable tracker for satellite monitoring of vehicles, motor bikes and other mobile objects.
It has no external antennas, so the installation process is quite simple.
T8808 versions: “A” and “B”
In comparison to basic model T8808B, which has no outputs, the model T8808A features one output – for engine block relay or any other control device:
- T8808A has 4 pin connector: Power, GND, ACC (orange) and Output (yellow)
The package contents:
- GPS tracker
- 4-pin harness (T8808A model)
- Sponge double-side adhesive tape
- Power supply extension line
Also as an option, manufacturer offers engine block relay for T8808A model.
Location and tracking
T8808A is embedded with GPS and doesn’t have support of GLONASS and alternative systems. It neither supports Assisted GPS technology. As the back-up, when no satellites signals are available, it uses Cell ID location (also known as LBS-tracking).
With Quad-band GSM 2G module T8808A can be operated all over the world.
With a voltage range 6-36V, it is possible to install T8808 both on cars and vans.
T8808 also features a built-in rechargeable backup battery. When fully charged it ensures about 2-3 hours of device operation (in normal conditions). When external power is cut off, the tracker sends location to server.
To switch the tracker OFF you need to remove the SIM card, after that in 5-10 seconds the device will switch off.
Local and remote management
T8808 tracker can be fully controlled over GPRS. There is also a wide list of SMS commands in a human-friendly format, on which device always replies back. It supports remote APN settings configuration by SMS.
T8808 has two LEDs:
- Red LED indicates GSM/GPRS mode
- Blue LED indicates GPS reception
The LEDs light goes out automatically in five minutes after the device is switched on.
The “ACC” wire of T8808 must be correctly connected. According to it, the device determines that vehicle is in use, switches GPS module to active mode and reports about its position to tracking server.
If there is no “ACC” signal, GPS module goes off and device does not send GPS coordinates. However, Cell ID information is updated regardless the “ACC” status.
There is also a “lifehack” which can be used for testing purposes or during the installation process: if you’re shaking the device within 60-70 seconds, GPS module will be enabled by accelerometer activity (regardless the “ACC” state) and device will update its location.
|EU platform||tracker.navixy.com (188.8.131.52)|
|US platform||tracker.us.navixy.com (184.108.40.206)|
|Peso||70 g (2.47 oz.)|
|Tamanho||81x38.5x13 mm (3.19x1.52x0.51 in)|
|À prova d\'água||IP6X|
|Antena interna (GNSS)||Yes|
|Antena externa (GNSS)||No|
|Tipo de rede celular||GSM Quad Band|
|Antena interna (Conexão)||Yes|
|Antena externa (Conexão)||No|
|Geração de rede celular||2G|
|Number of outputs||1|
|Number of inputs (all types)||2|
|Capacidade da bateria||280 mAh|
|Engine block relay||Yes|
|Fuel level sensor reading||Yes|
|Driver ID reading||No|
|Fuel temperature sensor reading||No|
|Engine block special control||Yes|
|Smart power consumption||No|
|External power cut off||No|
|Device switched on/off||Yes|
|GNSS satellites fixed||No|
|External power source voltage||No|
|Server connection setup over SMS||Yes|
|Remote device configuration||Yes (over GPRS), Yes|
|Message exchange format||BINARY|
|Firmware update OTA||No|
|Forced LBS location update over GPRS||No|
|Forced GNSS location update over SMS||No|