ATrack AU7

ATrack AU7 is the most advanced GPS/GLONASS vehicle tracking device that using CDMA/UMTS/HSPA mobile communication technology, with the flexibility of custom reporting mechanism for advanced users. It also gives the option of saving communication costs while keep the administrator to know the vehicle’s whereabouts in real time. In addition, the external accessory compatibilities, such as RS-232, CAN Bus interpreter, and 1-Wire®, give more options to meet all your project needs.

Mostrar más

Package contents

ATrack AU7 package contains the following device/accessories:

  • Device
  • GSM/UMTS Antenna
  • Serial Cable
  • GPS Antenna
  • Power/IO Cable


To support a wide range of hardware applications, the AU7 is equipped with a large number of inputs and outputs:

  • 6 Digital Inputs (IN0, IN1, IN2, IN3, IN4 and IN5):

IN0, IN1 and IN4 are positive triggers (Triggering Voltage Range: 3.7 ~ 40V). IN0 is dedicated to ACC (Ignition). IN2, IN3, and IN5 are negative triggers (Triggering Voltage Range 0 ~ 0.8V). These triggers can be used in the following application areas: Green/White engine detection, car door open/close detection, and Panic Button in case of any emergency.

  • 3 Digital Outputs (OUT1, OUT2, and OUT3):

They are normally used for engine or ignition immobilization. These digital outputs are open collector type. When in the “ON” state, these outputs are grounded (GND). When in the “OFF” state, it forms an open circuit.

  • 2 Analog Inputs (AN1 and AN2):

Each input is usually connected to an external temperature sensor or fuel level senor. The voltage range of AN1 is 0 ~ 40V 12-bits resolution. The voltage range of AN2 is 0 ~ 5V 12-bits resolution.

  • 1 Digital Output/Analog Input (OUT4/AN3):

This port may be configured as a digital output or analog input through the AT$IOCG command. The voltage range of AN3 is 0 ~ 40V 12-bits resolution.

  • 1-Wire:

It uses a single wire to transmit both data and power. You may use 1- Wire to connect up to 3 devices, for instance, one iButton and two temperature

Product features:

  • Flexible wireless network options
  • AES-128 data encryption
  • Data communication by SMS/USSD/TCP/UDP
  • GPS antenna tampered detect & report
  • Built-in 3-axis G-sensor
  • Vehicle Speed Sensor (VSS) supported
  • FOTA firmware upgrade using FTP
  • Configurable Real Time Tracking & Logging
  • 64 user defined geo-fences in circular, rectangular and polygonal shapes
  • Roaming preference settings
  • Harsh driving behavior events
  • Configurable power management
  • Max. 140,000 log and 21,000 queue messages
  • 2 way voice communication & wire-tap
  • 1-Wire® Dallas Key for driver identification
  • 1-Wire®temperature sensor supported
  • Support Garmin® FMI 2.0 and above
  • Intelligent event control engine

Location and tracking

ATrack AU7 is embedded with GPS. It is also available as GPS/GLONASS version.

As the back-up, when no satellites signals are available, it uses Cell ID location (also known as LBS-tracking).

Mobile networks

ATrack AU7 has a Quad-band GSM 2G module that allows to operate it all over the world.

Power supply

External power supply might be 8-40V, which makes possible to use ATrack AU7 with all car models.

Local and remote management

ATrack AU7 can be fully controlled over GPRS. There is also a wide list of SMS commands in a human-friendly format, on which device always replies back. It supports remote APN settings configuration by SMS.

LED Indication

ATrack AU7 model has three LEDs:

  • Power LED – indicates power status
  • GPS LED – indicates GPS signal
  • GSM LED – indicates GSMS signal

Integración de Servidor

Servidor de la (
Servidor de la (
Puerto de servidor47712

Información general



Peso100 g (3.53 oz.)
Tamaño100x65x26 mm (3.94x2.56x1.02 in)

Localización GNSS

Antena externa (GNSS)


Tipo de la red del celularGSM Quad Band
Antena externa (Conexión)
Generación de red celular2G


Número de Interfaces RSC2321
Número de salidas4
Número de entradas (todos tipos)8
Entrada ACC/ignisión
Entradas digitales
Entrada análoga
Interfaz RS232
Interfaz 1-Wire

Características de hardware

Capacidad de batería950 mAh
Batería integrada

Hardware extras

Lectura del identificador del conductor
On request
Lectura del sensor de la temperatura externa

Características de rastreo

Modos de rastreoContinuo
Localización por Cell ID
Consumo inteligente de batería
ECO driving

Monitoreo de eventos

Poca batería
Corte de alimentación externa
Jamming del señal móvil


Nivel de señal
Nivel de señal GNSS
Voltaje de alimentación externa
Nivel de batería interna


Tipo de lector CAN/OBDIIExterno

Administración remota

La conexión con servidor por SMS
Configuración remota de dispositivoSí (por GPRS), Sí
Control remoto de las salidasSí (por GPRS), Sí
Actualización de firmware OTA
Localización forzada de GNSS por SMS
On request


Active un dispositivo en la plataforma Probar
¿No ha encontrado su dispositivo? Podemos añadirlo Integrar
Rastreo 3.0 NEW
Rastreo 3.0 NEW
Miles de objetos.
Intuitiva UX.
Poderoso diseño.
Saber más >

Este sitio usa cookies.
Revise nuestra Política de Privacidad para saber más.

Do you want to switch to English version?

Yes No