menu

AMGPS T-1100

AMGPS T-1100 is marketed by the manufacturer as light real-time tracking terminal. It works with GPS and GLONASS systems and it is able to connect to GSM networks. It can be used for the work's optimization of fleet management also transport companies as well as for personal needs.

Mostrar más

This GPS tracker has an internal GSM and GPS/GLONASS antennas and is able to catch not the strongest signals. Also, T-1100 has a smart power consumption system that can extend the life of the built-in battery in deep sleep mode.

It is operating in different roaming networks and due to a smart algorithm of GPRS connections help to save the traffic.

Package contents

Package content depends on order code, and can be customized by customer needs.

The standard package contains:

  • Input and output power supply cable with a 2×5 connection pins
  • USB cable
  • A card containing URL to download FM1120 device drivers and Configurator software
  • Integrated 170mAh Li-ion rechargeable battery

Location and tracking

T-1100 model is embedded with GPS chip and also it has the support of GLONASS. It doesn’t support Assisted GPS (A-GPS) technology. As the back-up, when no satellites signals are available, it uses Cell ID location (also known as LBS-tracking).

The tracking mode is flexible configured: by moving every 100m, and every 60 sec, and on turning on 30 degrees by default. When there is no movement (detected by “Ignition” status), tracker sends data every 180 seconds.

Mobile networks

T-1100 has a quad-band GSM 2G module, so it can be operated all over the world.

Interfaces

T-1100 model features such interfaces as

  • 1 Digital Input Reserved for Ignition Status Monitoring
  • 2 Digital Inputs
  • 1 Analog Input (10V or 30V range)
  • 2 Digital Open-collector Outputs (connecting external relays, LED, buzzers etc.)
  • 1-Wire® temperature sensor
  • 1-Wire® iButton
  • Motion sensor
  • USB Port

Power supply

T-1100 uses and voltage range 10-30V, which makes possible to install it both on cars and trucks. Device also features an optional built-in rechargeable backup battery. When fully charged it ensures about 1 hour of device operation (in normal conditions).

“Ignition” status

There is a virtual “Ignition” flag in T-1100 which is determined by either:

  • External power voltage – when the power level falls below a certain configured level (by default 13V), the “Ignition” is considered to be OFF, otherwise – ON.
  • Digital Input #1 – if there is positive signal on DIN #1 of the socket, the “Ignition” flag is ON.
  • Acceleration sensor – when the built-in accelerometer detects movement, the “Ignition” flag is ON.

“Stop/Movement” mode

AMGPS T-1100 determines whether vehicle is on move or stopped by one of three methods (configurable by user):

MethodMovingStopped
by Board VoltageIf board voltage exceeds certain level (configurable, 13V by default)If board voltage is lower than a certain level
by AccelerationInternal accelerometer detects movementInternal accelerometer does not detect movement
by GNSSGNSS is fixed and speed is above 5 km/hGNSS is fixed and speed is below 5 km/h  or GNSS is not fixed

Two sleep modes

T-1100 is able to go to Sleep mode after configurable Sleep timeout. This timeout (defined period) starts counting when device is in STOP mode. After timeout is reached and all conditions for sleep mode are met, device goes to normal sleep or deep sleep mode:

  • Normal sleep mode. While in normal sleep mode, T-1100 turns GNSS module OFF, but keeps GSM module ON. The device is not making any new periodic GPS records, just monitoring the events with the last known coordinates and sends them to tracking server. As a result power consumption decreases allowing saving vehicle’s battery (below 2 mA).

T-1100 exists normal sleep mode when “Movement” mode detected or “Ignition” switches on.

  • Deep sleep mode. While in deep sleep mode, T-1100 sets both GNSS receiver and GSM/GPRS module to OFF state, thus making impossible to wake up the device remotely. Battery consumption drops below 2 mA.

T-1100 exits deep sleep mode if at least one of following conditions is true:

  • “Movement” mode is detected
  • “Ignition” is turned on
  • USB cable is connected

Harsh driving behaviour

T-1100 features “Green Driving Scenario” that helps to inspect driver about harsh driving. Scenario continuously monitors: accelerating force, braking force and cornering angles. When these parameters exceed configured thresholds, Green Driving event is generated and sent to server

To prevent generating false events, harsh acceleration and harsh braking is monitored only when following conditions are fulfilled:

  • “Ignition” flag (see above) is turned on
  • Vehicle speed is equal or higher than 10 km/h

Harsh cornering is monitored only when following conditions are fulfilled:

  • “Ignition” flag (see above) is turned on
  • Vehicle speed is equal or higher than 30km/h

Local and remote management

AMGPS T-1100 tracker can’t be controlled over GPRS, though it supports firmware updating via GPRS (FOTA). However, there is a wide list of SMS commands in a ASCII  format, on which device always replies back. In particular, Server address and port, APN settings can be applied remotely with SMS. To decrease the amount of SMS required for configuration SMS in binary format can be also used.

You can also configure T-1100 from a PC using proprietary software (Teltonika Configurator) and standard USB-cable which is included into package.

LED Indication

T-1100 has two status LEDs:

  • Status LED: indicates GSM/GPRS mode
  • Navigate LED: indicates GPS reception

Integración de Servidor

Servidor de la EUtracker.navixy.com (52.57.1.136)
Servidor de la UStracker.us.navixy.com (13.52.37.2)
Puerto de servidor47776
Integrado06/02/2015

Información general

PurposeVehículo
InstalaciónProfesional

Alojamiento

Peso80 g (2.82 oz.)
Tamaño65x56.6x18.9 mm (2.56x2.23x0.74 in)

Localización GNSS

Antena interna (GNSS)
Antena externa (GNSS)No
GPS
GLONASS

Conectividad

Tipo de la red del celularGSM Quad Band
Antena interna (Conexión)No
Antena externa (Conexión)No
Generación de red celular2G

Interfaces

Número de salidas2
Número de entradas (todos tipos)3
Entradas digitales
Soportado
Entrada análoga
Soportado
Interfaz 1-Wire
Salidas

Características de hardware

Capacidad de batería170 mAh
Batería integrada
El botón de pánicoNo

Hardware extras

Lectura del identificador del conductor
Soportado

Características de rastreo

Modos de rastreoIntervalo, Continuo
Localización por Cell ID
Soportado
Consumo inteligente de batería
Soportado
ECO driving
Soportado

Monitoreo de eventos

Poca batería
Soportado
Cambio de entrada
Soportado
Corte de alimentación externa
On request

Automonitoreo

Nivel de señal
Soportado
Nivel de señal GNSS
Soportado
Satélites GNSS fijados
Soportado
Voltaje de alimentación externa
Soportado
Nivel de batería interna
Soportado

Administración remota

La conexión con servidor por SMS
Soportado
Configuración remota de dispositivoSí (por SMS), Sí
Control remoto de las salidasSí (por SMS), Sí
Actualización de firmware OTA

Certificacón

CE
FCC
Active un dispositivo en la plataforma Probar
¿No ha encontrado su dispositivo? Podemos añadirlo Integrar
Rastreo 3.0 NEW
Open
Rastreo 3.0 NEW
Miles de objetos.
Intuitiva UX.
Poderoso diseño.
Saber más >
Open

Este sitio usa cookies.
Revise nuestra Política de Privacidad para saber más.

Do you want to switch to English version?

Yes No