Contact us Login LIVE DEMO FREE TRIAL

YA TUT 1.0

Supported features

Server Integration
Server Addresstracker.navixy.com
Server IP Address217.23.132.215
Server port47725
General information
PurposeVehicle
InstallationProfessional
Housing
Weight70 g (2.47 oz.)
Size110x75x20 mm (4.33x2.95x0.79 in)
Waterproof classIP5X
GNSS Location
Internal antenna (GNSS)
External antenna (GNSS)Yes
GPSYes
GLONASSYes
Connectivity
Cellular network typeGSM Quad Band
Internal antenna (Connection)
External antenna (Connection)Yes
Cellular network generation2G
Interfaces
1-Wire interfaceYes
RS232 interfaceYes
Number of RS232 interfaces1
RS485 interfaceYes
Number of outputs8
Number of inputs (all types)8
ACC/Ignition inputYes
Supported
Discrete inputsYes
Supported
Analog inputsYes
Supported
Impulse inputsYes
Supported
Frequency inputsYes
Supported
OutputsYes
Supported
Hardware features
Battery capacity600 mAh
Built-in batteryYes
Emergency buttonYes
Supported
Detach sensor
Non-volatile memory
Engine block relayYes
Supported
AccelerometerYes
Hardware extras
Fuel level sensor readingYes
Supported
Voice listeningYes
Supported
Emergency buttonYes
Supported
Driver ID readingYes
Supported
Fuel temperature sensor readingYes
Supported
Engine block special controlYes
Supported
External temperature sensor readingYes
Supported
Voice communicationYes
Supported
Fuel flow meter readingYes
Supported
Tracking features
Tracking modesContinuous, Interval
Location by Cell IDYes
Supported
Smart power consumptionYes
Supported
Odometer
ECO driving
Events monitoring
Battery lowYes
Supported
Input changeYes
Supported
SIM card slot openYes
Supported
Self monitoring
External power source voltageYes
Supported
Internal battery levelYes
Supported
CAN/OBDII reading
CAN/OBDII reader typeInternal
Supported
Remote management
Server connection setup over SMSYes
Supported
Remote device configurationYes (over GPRS)
Supported
Remote outputs controlYes (over GPRS)
Supported
Device ID typeStatic (IMEI)
Firmware update OTA
Certification
CEYes
FCCYes

How to connect to Navixy server

YA TUT 1.0 is tightly integrated with this software platform.

Activation process

Automatic activation (recommended)

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode though the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

When you activate a device, the following SMS commands are sent from server to device:

SMS command from

Server to Device

SMS reply from

Device to Server

Command

explanation

setgprs <IP>:<PORT>,<APN>,<Login>,<Password> setgprs <IP>:<PORT>,<APN>,<Login>,<Password> OK Activating device setup

Some parameters will depend on your cellular network operator:

  • <APN> – APN name
  • <Login> – APN login
  • <Password> – APN password

As soon as these commands are executed the GPS tracker will connect to the server, and the rest of configuration process will be done via GPRS channel.

Manual configuration

If you experience issues with the SMS delivery from the platform to device in your country, you can setup device manually by sending the command above from your mobile phone or using native “YATUT-Configurator” software.

You should enable fuel level sensor and CAN manually. You can do it through the proprietary software (YATUT-Configurator), by selecting the device and applying command to it.

Activate a device on the platform Try it now

Haven’t found your device? We can add it Integrate

Contacts

USA: +1 858 815 9045

Mexico: +52 334 1642158

UK: +44 808 1641499

Germany: +49 1573 5988250

Russia: +7 495 317 1622

Log in

Loading...

We use сookies to improve our website, products and related services, analyze site traffic, and serve targeted advertisements. If you continue to use our services, you consent to our use of сookies. Read more