TopFlyTech T8808A+

TopFlyTech model T8808A+ is a compact and affordable tracker for satellite monitoring of vehicles, motor bikes and other mobile objects. It has no external antennas, so the installation process is quite simple.

Show more

T8808+ versions: “A” and “B”

In comparison to basic model T8808B+, which has no ouputs, the model T8808A+ features one output – for engine block relay or any other control device:

  • T8808A+ has 4 pin connector: Power, GND, ACC (orange) and Output (yellow)

Package content

The package contents:

  • GPS tracker
  • 4-pin harness (T8808A+ model)
  • Sponge double-side adhesive tape
  • Power supply extension line

Also as an option, manufacturer offers engine block relay for T8808A+ model.

Location and tracking

T8808A+ is embedded with GPS and it supports GLONASS and alternative systems. It also supports Assisted GPS technology. As the back-up, when no satellites signals are available, it uses Cell ID location (also known as LBS-tracking).

Mobile networks

With Quad-band GSM module T8808A+ can be operated all over the world.

Power supply

With a voltage range 6-36V, it is possible to install T8808+ both on cars and vans.

T8808+ also features a built-in rechargeable backup battery. When fully charged it ensures about 2-3 hours of device operation (in normal conditions). When external power is cut off, the tracker sends location to server.

To switch the tracker OFF you need to remove the SIM card, after that in 5-10 seconds the device will switch off.

Local and remote management

T8808+ tracker can be fully controlled over GPRS. There is also a wide list of SMS commands in a human-friendly format, on which device always replies back. It supports remote APN settings configuration by SMS.

LED Indication

T8808+ has two LEDs:

  • Red LED indicates GSM/GPRS mode
  • Blue LED indicates GPS reception

The LEDs light goes out automatically in five minutes after the device is switched on.

Additional notes

The “ACC” wire of T8808+ must be correctly connected. According to it, the device determines that vehicle is in use, switches GPS module to active mode and reports about its position to tracking server.

If there is no “ACC” signal, GPS module goes off and device does not send GPS coordinates. However, Cell ID information is updated regardless the “ACC” status.

There is also a “lifehack” which can be used for testing purposes or during the installation process: if you’re shaking the device within 60-70 seconds, GPS module will be enabled by accelerometer activity (regardless the “ACC” state) and device will update its location.

Server Integration

EU (
US (
Server port47744

General information



Weight70 g (2.47 oz.)
Size81x38.5x13 mm (3.19x1.52x0.51 in)
Waterproof classIP6X

GNSS Location

Internal antenna (GNSS)Yes


Cellular network typeGSM Quad Band
Internal antenna (Connection)Yes
Cellular network generation2G


Number of outputs1
Number of inputs (all types)2
ACC/Ignition inputYes
Discrete inputsYes

Hardware features

Battery capacity280 mAh
Built-in batteryYes

Tracking features

Tracking modesInterval, Continuous
Location by Cell IDYes
ECO drivingYes
On request

Events monitoring

Battery lowYes
External power cut offYes
Car crashYes
On request

Self monitoring

GNSS signal levelYes
Internal battery levelYes

Remote management

Server connection setup over SMSYes
Remote device configurationYes (over GPRS)
Remote outputs controlYes (over GPRS)
Message exchange formatBINARY


Activate a device on the platform Try it now
Haven’t found your device? We can add it Integrate
Tracking 3.0 NEW
Tracking 3.0 NEW
Thousands of objects.
Intuitive UX.
Powerful design.
Learn more >

This website uses cookies.
See our Privacy Policy to learn more.