Meitrack MT90

Meitrack MT90 is a handheld and simple-to-use GPS/GLONASS tracker that can be used for personal or pet tracking. Due to its small size this device may be used by parents to track the location of their kids.11111111

Supported features

Server Integration
Server IP Address217.23.132.215
Server port47752
Integrated on23/09/2013
Revised on09/10/2013
General information
PurposePersonal, Pet
InstallationNot required
Weight70 g (2.47 oz.)
Size77x47x20 mm (3.03x1.85x0.79 in)
Waterproof classIP6X
GNSS Location
Internal antenna (GNSS)Yes
Cellular network typeGSM Quad Band
Internal antenna (Connection)Yes
ACC/Ignition input
Hardware features
Battery capacity1100 mAh
Built-in batteryYes
Events monitoring
Battery lowYes
External power cut offYes
Self monitoring
GNSS signal levelYes
GNSS satellites fixedYes
Remote management
Server connection setup over SMSYes
Remote device configurationYes (over GPRS)

How to connect to Navixy server

Automatic activation (recommended)

The software platform supports automatic device activation by applying APN settings, server address and port, as well as recommended tracking mode though the SMS channel. Normally you don’t need to configure anything manually. Just install the SIM card, switch the device ON and make sure it is located in the place with good GPS signal reception.

You also need to keep the device with initial factory settings, in particular:

  • Do not set any password, keep it clear (as by default)
  • Do not set any master number prior to the device activation
  • Do not set local Time zone, it must be UTC+0h (as by default)

Manual configuration

If the automatic activation failed, you can configure Meitrack MT90 manually by sending these command:

<tracker password>,A21,1,,47752,<APN>,<APN username>,<APN password>

  • <tracker password> – the default password for tracker settings, usually it is 0000
  • <APN> – APN of your GSM provider
  • <APN username> – username of APN, if any
  • <APN password> – password of APN, if any

Also you can configure Meitrack MT90 via Meitrack configurator.

For this you need

  1. Install the USB-to-serial cable driver and Meitrack Manager.
  2. Connect the MT90 to a PC with the USB-to-serial cable.
  3. Run Meitrack Manager, then the following dialog box will appear:
  4. Meitrack Manager
  5. Meitrack Manager will detect the device model automatically and the parameter page will appear accordingly.

Note: The CD delivered with the tracker contains Meitrack Manager. The software language will be automatically switched according to the operating system language. Press Ctrl + L to manually switch the language.

Activate a device on the platform Try it now

Haven’t found your device? We can add it Integrate

More about Meitrack in our blog

  • Meitrack T355: a king of asset GPS trackers

    Meitrack T355 a kind of GPS devices born to be successful on a market. The reason is a combination of simplicity and functionality based on special demands from asset GPS trackers. A rule of thumb states that these factors are crucial to make a real best-seller.…

  • Meitrack T355 and T333
    Integration: Meitrack T355 and T333 (3G)

    We continue to work towards providing the best user experience in GPS tracking by integrating all the latest GPS devices. Today it’s about two new models from Meitrack – T355 and T333, that puts the total amount of supported devices of this manufacturer to 10.…


USA: +1 858 815 9045

Mexico: +52 334 1642158

UK: +44 808 1641499

Germany: +49 1573 5988250

Russia: +7 495 223 0427

Log in


We use сookies to improve our website, products and related services, analyze site traffic, and serve targeted advertisements. If you continue to use our services, you consent to our use of сookies. Read more